2012 Bmw 5 Series Brake Pad Reset

BMW 5-Series service reset procedure. This vehicle is a push to start.

Bmw 5 Series Service Reset F10 F11 F07 Mr Fix Info

Use trip reset button to choose reminder to reset.

2012 bmw 5 series brake pad reset. I can cycle through all the things that I can reset and it says reset possible. Release the button briefly and push it in again and hold for about 5 10 seconds until the new date appears in. Turn on the ignition but do not start the car.

In some cases you may have to perform the BMW brake reset procedure more than once. How to reset oil service brake pad service indicator -----1. Resetting front brake pad.

You can reset the brake pad interval via the instrument cluster. Wait until everything in the instrument display has settled. Resetting took them back to over 30000 miles again much more inline with the wear rate for the first part of the pad.

However my light is still on. Release the trip rest button and press again but hold down the trip reset button to start the reset process. 0 How to reset oil service brake pad service indicator.

Have you checked the brake fluid. Release the button as soon as first service procedure is visible on the screen. Below is a link to a picture I just took.

You will notice your trip meter reset and then go. Then press and hold until it says reset then release and press and hold again to reset the light. Brake pads must have at least 80 life remaining.

Without pressing the brakeclutch press the startstop button. By pressing an holding down the trip reset button the dash now enters the service reset mode. What made the difference for me was on the last step when the car would display ------ just before it normally would display the -15k I cut the car off while holding the reset button down didnt work without this part.

Press and hold the reset button until the hidden menu comes up. I have a 2012 BMW 740i and I am looking to reset my brake light. Any support you can lend to resolve my problem would be greatly appreciated.

Hold down the trip reset button in the instrument cluster. Still holding down the trip reset button will display this. The old CBS issue being way off.

You will notice your trip meter reset and then go back to the value it once was. After completing the above three steps the brake pad lights should reset. I tried the reset process above countless times and it would only reset to -15000thats a negative 15K.

Had a similar issue with my rear pads garage reset CBS as 8mm measured thickness is thousands of miles of use. Press and hold the odometer reset button. Everything went smooth except when I try to reset the service light Im getting a message that says reset unsuccessful.

Without pressing the brakeclutch press the startstop button 2. Insert the key or key fob in the ignition. 3mm is the typical minimum pad thickness wed safely run.

Move the key to position 2 but dont start the ignition. Turn on the ignition without starting the engine so that all the dash lights come on. So I hold the odometer button down.

Press and hold trip reset button and wait for the service icon to appear. Once you are on the rear brakes release and hold in for a futher 5 seconds and then release and that should be it. If your BMW has a START button press it without pressing the brake pedal.

I have had the front and rear brake pads as recommended by the system. BMW brake light reset procedure can be performed for front or rear brakes. If you want to reset the Brake Fluid interval for another 2 years then keep holding the odometer button until the word RESET appears at the bottom of the lower window.

Front brakes rotors and pads rear brakes rotors and pads. Hows the level and when was it last changed. Keep holding for a couple more seconds.

Turn on the ignition. Wait for the service reminder to disappear 3. Open the drivers door and wait for approximately 10 seconds.

Make sure all the doors are shutswitch on the ignition and wait about 6 secondspress the cluster reset button and keep it pressed untill you see the service menueach press will take you to the next item you want to reset. Reset BMW Brake Wear Reminder Using Hidden Menu If resetting BMW brake pad wear using the normal reset procedure fails try resetting using the hidden menu. The reset menu is found by I think pressing the BC button on the indicator stalk holding in the trip reset button in the instrument pod until you see a service picture scrolling through by tapping the reset button until you reach brake pads and then hold for seconds until it asks if you want to reset tap reset for yes and then hold for seconds until resetting shows.

Brake Pad warning reset fail and constant red inspection Post by you loves it Wed Apr 04 2012 435 pm change the sensor then with the engine running press and hold the trip mileage button until the exclamation mark pops up. BMW I-Drive Reset. The reset procedure is as follows.

Turn on the ignition. Wait for the service reminder to disappear. Get in the car and close all the doors.

Hey Guys I just replaced the rear pads and rotors on my 2014 328d. Press and hold the odometer reset button.

F10 535i Front Brake Service Reset Diy F07 F10 F11 2010 2017 Bmw 5 Series Owners Board